A phone that survived a dunk in the bath, a pair of earbuds that endured a rainy run, a speaker left beside a pool: the stories that people tell about waterproof devices are often confident, and sometimes wrong. The label behind them is a two digit code that looks technical and precise, and it is, but it describes a laboratory test under narrow conditions that real life rarely matches, and the code does not mean the product is waterproof.
This guide explains what each digit means, how the common ratings such as IPX4, IP67 and IP68 are tested, why IP68 does not mean the same depth on every product, which liquids and conditions the tests do not cover, how seals deteriorate, and what warranties usually say. It aims to give you a realistic picture of what a rating protects against.
What the two digits mean
IP stands for ingress protection, and the code is defined in an international standard, IEC 60529. It has two digits. The first digit, from 0 to 6, describes protection against solid objects, from large body parts down to fine dust. The second digit, from 0 to 9, describes protection against water, from none, through dripping and spray, to immersion and high pressure jets.
A higher number means greater protection, but the scales are not simple ladders. When a digit is replaced by the letter X, it means the product was not tested for that category, not that it failed. IPX4 means the product was tested for water splashing and not for dust. A rating of IP6X would be dust tight but with no stated water protection.
The code describes a single test of a new product under standard conditions. It is a statement that the product passed that test, not a guarantee of how it will behave for years of use. It is also self declared in many cases, since a manufacturer may test in house or at a laboratory, and no source documents that every rating on every box has been independently verified.
| Digit | Meaning of the first digit (solids) | Meaning of the second digit (water) |
|---|---|---|
| 0 | No protection | No protection |
| 4 | Objects larger than 1 mm | Water splashed from any direction |
| 5 | Dust protected, limited ingress | Low pressure water jets |
| 6 | Dust tight | Powerful water jets |
| 7 | Not applicable | Immersion up to 1 metre for 30 minutes |
| 8 | Not applicable | Continuous immersion under conditions set by the maker |
The first digit: dust and solids
For most consumer electronics, the first digit that matters is 5 or 6. A rating of 5 means the product is protected against dust, though a small amount may get in without harming operation. A rating of 6 means dust tight, with no ingress of dust in a test where the product sits in a chamber of fine powder under a slight vacuum. Lower numbers protect against larger objects, such as fingers or tools.
Dust protection matters more than people expect. Fine sand and grit can scratch moving parts and clog charging ports and buttons, and a dust tight design keeps the interior clean. For phones and earbuds, a 6 in the first position is the usual target, and many products with an X in that position are only tested for water.
The test uses a specific fine powder and conditions, and real dust such as flour, beach sand with moisture or cement dust may behave differently. A dust tight rating also assumes ports and covers are properly closed. If a product has a flap or plug over a port, it must be fully seated for the rating to apply, and an open flap voids the protection.
The second digit: from splashes to immersion
The water digit is the one most people care about. A rating of 4 means the product withstands splashing from any direction, a sensible level for earbuds and fitness bands used in the rain or in the gym. A rating of 5 and 6 cover jets of water, tested with a nozzle at a stated flow and distance, relevant to outdoor gear and cleaning.
A rating of 7 means the product survives immersion in fresh water to a depth of 1 metre for 30 minutes. A rating of 8 means it survives continuous immersion beyond that, under conditions agreed between maker and buyer, which in practice means the maker defines the depth and time. There are also ratings 9 and 9K, for high pressure, high temperature jets, used for industrial and vehicle equipment.
Splash and jet ratings are not about immersion. A product rated for splashes is not designed to be dropped in a pool, and one rated for immersion is not necessarily rated for strong jets. A phone may be listed as IP68 and still be damaged by a powerful jet from a shower head. The categories test different forces, and the ratings do not imply each other, which is why some products carry two codes.
Why IP68 does not mean the same thing everywhere
IP67 has a fixed definition: 1 metre for 30 minutes. IP68 does not. The standard says only that the conditions must be more severe than for IP67 and must be agreed between the manufacturer and the user. That means one phone may be rated for 1.5 metres for 30 minutes, another for 6 metres for an hour, and both are IP68.
The depth and time are usually listed in the technical specifications, not on the box, so check them. A larger number is not necessarily better for your use, since a phone rated to a greater depth was tested under conditions that you will not meet. For everyday risks such as a drop in the sink, a toilet or a puddle, 1 metre is ample, and what matters more is the condition of the seals.
Be careful with comparisons between brands. Two phones sold as IP68 may differ in depth, duration and in the tests that the maker ran in addition. Wearables and earbuds with IP68 may have the rating for the earbuds but not for the charging case, which often carries a lower rating or none at all. Look at what part of the product the rating applies to.
What the tests do not cover
The immersion tests use clean fresh water at room temperature. Salt water is more corrosive and conductive, and can get into seals and damage contacts, so a phone rated for fresh water is not safe at the beach unless the maker says so. After any salt exposure, rinse the device with fresh water and dry it, if the manual says that is acceptable.
Chlorinated pool water, soapy water, shampoo, sunscreen and similar liquids can attack seals and adhesives, and are not part of the test. Hot water and steam are also excluded: a hot shower, a sauna or a steam room can cause pressure changes and seal damage that the room temperature test does not reflect. Many manufacturers say plainly not to use devices in these conditions, and warranty terms often follow.
Pressure and movement are other factors. The test is static, with the product sitting under water, while swimming, diving or a water slide involve dynamic pressure, impacts and temperature changes. A device rated for immersion may leak at the force of a swimmer's stroke or a dive. Check whether the maker specifically rates a product for swimming, as some do, and treat that statement as separate from the IP code.
Seal aging and drops
Water resistance depends on rubber gaskets, adhesives and tight tolerances, and all of them age. Gaskets harden, adhesives weaken with heat and flexing, and a case that has been opened for repair may not seal as well afterwards. A rating measured on a new product is a ceiling, and every year of use erodes it, so older devices are less reliable even if they look unchanged.
Drops and impacts matter as much. A fall that does not crack the screen may still open a micro gap in the frame, or loosen a seal. After a hard knock, treat water resistance as reduced. The same applies to a cracked screen or back, a damaged charging port and any repair, since these breach the original seal.
Practical care helps. Keep ports and plugs clean, avoid exposing devices to heat, such as the dashboard of a car, which degrades adhesives, and avoid charging a device that is wet, since moisture in a port can short out the connection. If a device does get wet, dry it before charging, as discussed in USB-C charging standards explained, and do not use rice or heat, which are unreliable remedies. A power bank is not generally waterproof either, as noted in power bank capacity explained.
One non-obvious point concerns ports and speakers. A device can be sealed against immersion and still have a speaker grille or microphone hole that holds water afterwards, muffling sound for hours. Many phones and earbuds have a way to eject water through vibration, and tilting the device with the speaker down helps. Do not use compressed air or a hair dryer, which can push water further in or damage the membranes.
Another is the charging port. Water trapped in a port can cause corrosion within days if power is applied, and many phones warn you when moisture is detected and block charging for that reason. Respect the warning, wait until the port is dry, and use wireless charging if the device supports it. Corrosion is a slow failure that appears weeks later, and it is the reason many wet devices die after seeming to recover.
Finally, remember that a rating applies to the device as sold, with its accessories in the state described. A case, a screen protector or a charging cradle does not change the code, but a poorly fitted case can trap moisture against ports. Wash a case separately, remove it to dry the device after a soaking, and replace damaged covers on ports at once, since a torn plug cancels the protection it was meant to provide.
Warranty exclusions
Most manufacturers state that water damage is not covered by the warranty, even for products with a water resistance rating. They advertise the rating as a feature, but treat any liquid damage as a result of user conditions. If a rated phone fails after a swim, the warranty may be refused if the damage indicator inside the device has been triggered.
Read the fine print of the specification. It often says that water resistance is not permanent, may reduce over time and is not a reason for a claim. Some brands offer limited liquid damage cover in a paid protection plan or an accidental damage policy, which can be more valuable than the rating itself. Check what is covered, and under which conditions.
Keep records, such as receipts and photos, and follow the care instructions, since failure to do so may be used to deny a claim. If you buy a product for water use, such as a swim safe watch or earbuds, look for a statement from the maker about the specific activities it supports, not only the IP code. Browse the tech and electronics category for related guides.
Matching the rating to the device
For earbuds and headphones used for exercise, IPX4 is enough to handle sweat and rain, and a higher rating gives a margin for heavy sweat and washing. The audio features of such devices, such as noise cancelling, are explained in how noise cancelling headphones work. Remember that the case may have a lower rating than the earbuds.
For phones, IP67 or IP68 gives reassurance against rain, spills and accidental dunks, though not against deliberate use underwater. For outdoor speakers, look for a rating for splashes at least, and for those used by a pool, a rating for immersion, plus a mention of chlorine. For cameras, action cameras and watches that are used in water, check the depth rating and whether a separate case is needed.
For household devices such as smart sensors, doorbells and cameras mounted outdoors, ratings in the IP65 and IP66 range suit rain and hose spray, and a second digit of 4 or higher suffices for sheltered spots. The right rating depends on the exposure, so match the code to the real conditions and add a safety margin where the device is hard to replace or access.
Frequently asked questions
Does IP68 mean I can swim with my phone?
Not necessarily. The test is static, in clean fresh water, and does not cover pool chemicals, salt water or the pressure of movement. Many makers advise against swimming or diving with phones, and warranties may exclude water damage, so treat IP68 as protection against accidents.
What is the difference between IPX7 and IP67?
IPX7 was tested only for water, with the dust test not done. IP67 was tested for both dust and water. Both survive the same immersion of 1 metre for 30 minutes. IP67 gives extra assurance against dust.
Can hot water or steam damage a rated device?
Yes. Tests use room temperature fresh water, and heat can weaken seals and cause pressure changes. Avoid showers, saunas and steam rooms unless the maker explicitly says the device is suitable.
Does water resistance last forever?
No. Seals and adhesives age, and drops or repairs can open gaps. A rating applies to a new product. Treat the resistance of an older device as lower and avoid risky exposure.
What should I do if my device gets wet?
Switch it off, dry the outside, and let it air dry in a well ventilated place. Do not charge it until the port is dry. Avoid heat and rice. If it does not work afterwards, contact the maker or a repair service.
Is IPX4 enough for running earbuds?
For sweat and light rain, yes. Heavy rain or rinsing under a tap may exceed it. If you run in all weather, consider a higher rating. Remember that the charging case is usually less protected.
The bottom line
Read an IP rating as a lab result for a new product in clean fresh water, not as a promise of waterproofing. The first digit covers dust, the second water, and an X means not tested. IP67 has a fixed definition, while IP68 depends on the maker's stated depth and time, so check the specification.
Choose the rating to match the real exposure: IPX4 for sweat and rain, IP67 or IP68 for phones and gear that may be dunked, and a stated swim rating if you will actually swim. Remember that salt, chlorine, soap and hot water are outside the test.
Treat water resistance as a margin for accidents that fades with age, and keep ports dry, seals intact and expectations modest. Do not rely on the warranty to cover liquid damage, and look for accidental damage cover if the risk is real.